剪切解络-超滤分离金属关键指标预测与验证

根据剪切解络-超滤过程中金属离子的动态浓度关系和质量守恒定律,采用CodeBlocks17.12软件编写程序,建立了剪切解络-超滤工艺关键指标预测模型,实现了金属离子浓度、回收率、体积稀释倍数等指标的预测,并用实验加以验证。依次在转速800 r/min、1 400 r/min、3 000 r/min下回收模拟废水中43 μg/L的Co²⁺、995 μg/L的Ni²⁺和88 μg/L的La³⁺,3种金属的回收率均达99.8%以上时,超滤过程体积稀释倍数的预测值分别为7.0、7.5、5.75,实验值分别为7.5、7.25、6.25,可见预测值与实验值基本一致。本模型对研究方案制定和调整有实际指导意义。     

A kinetic model involving oxidation and volatilization in SiC-B4C-xAl2O3 ceramics system

In this paper, a new kinetic model considering both oxidation and volatilization kinetics is established and applied to analyze the oxidation of SiC-B₄C-xAl₂O₃ ceramics and other systems in various oxidation conditions. The effects of diffusion area and volume changes during the oxidation process are considered in this model. The physical meaning of each parameter in this model is explicit and simple. According to this model, the diffusion coefficient of species and the corresponding diffusion activation energy are easily available. The practicability of this model is well verified by the experimental data of SiC-B₄C-xAl₂O₃ and other systems oxidized under different conditions. In addition, the practice shows that the model is applicable not only to the systems where oxidation and volatilization coexist, but also to the system where only oxidation plays a major role. We hope the model proposed in this work can be used in other materials with more complex environments.     

Trimetallic NiFeCr-LDH/MoS2composites as novel electrocatalyst for OER

The development of efficient and stable oxygen evolution reaction (OER) catalysts is an ongoing challenge. In order to solve the problem of low oxygen evolution efficiency of the current OER catalysts, a novel material was synthesized by the incorporation of NiFeCr-LDH and MoS₂, and its structural and electrochemical properties were also investigated. The introduction of MoS₂ improves the electrochemical performance of NiFeCr-LDH. The polarization curve shows that the potential of composite material is only 1.50 V at a current density of 10 mA cm^?2, which is far superior to commercial precious metal catalysts. In addition, the stability experiment shows that the composite material has excellent stability, and the current density has little change after 500 cycles. Furthermore, we found that some metal ions, such as Ni, Cr and Mo, exist in the form of high valence on the surface of NiFeCr-LDH@MoS₂, which is also conducive to the occurrence of oxygen evolution reaction.     

Black phosphorous nanosheets–gold nanoparticles–cisplatin for photothermal/photodynamic treatment of oral squamous cell carcinoma

To improve five-year survival rate of oral squamous cell carcinoma (OSCC), the development of a novel composite material of black phosphorus nanosheets (BPNSs) and gold nanoparticles (AuNPs) for tumor treatment was carried out. The purpose of this study is to evaluate the cytostatic effects of BPNSs, AuNPs loaded with cisplatin (CDDP) on human tongue squamous cell carcinoma cells lines (SCC-9), and 7,12-dimethylbenz anthracene induced cheek squamous cell carcinoma was validated in golden hamsters animal models. The results showed that BPNSs could efficiently inhibit the metastasis and growth of OSCC compared with CDDP and AuNPs. And a combination composite of AuNPs–BPNSs loaded with CDDP could more effectively inhibit the metastasis and growth of OSCC, which might be due to the high drug-loading capacity, excellent photothermal properties and the combination of photodynamic and photothermal therapy of BPNSs and AuNPs, as well as the synergistic effects of AuNPs, BPNSs and CDDP.     

ZnIn2S4/In(OH)3 hollow microspheres fabricated by one-step l-cysteine-mediated hydrothermal growth for enhanced hydrogen production and MB degradation

An intervening barrier for photocatalytic water decomposition and pollutant degradation is the frustratingly quick recombination of e⁻ - h⁺ pairs. Delicate design of heterojunction photocatalysts by coupling the semiconductors at nanoscale with well-matched geometrical and electronic alignments is an effective strategy to ameliorate the charge separation. Here a facile and environment-friendly l-cysteine-assisted hydrothermal process under weakly alkaline conditions is demonstrated for the first time to fabricate ZnIn₂S₄/In(OH)₃ hollow microspheres with intimate contact, which are verified by XRD, SEM, (HR)TEM, XPS, N₂ adsorption-desorption, UV–Vis DRS and photoluminescence spectra. ZnIn₂S₄/In(OH)₃ heterostructure (L-cys/Zn²⁺ = 4, molar ratio) with a band-gap of 2.50 eV, demonstrates the best photocatalytic performance for water reduction and MB degradation under visible light, outperforming its counterparts (In(OH)₃ and ZnIn₂S₄). The excellent activity of ZnIn₂S₄/In(OH)₃ heterostructure arises from the intercrossed band-edge positions as well as the unique hollow structure with large surface area and wide pore-size distribution, which are beneficial for the efficient charge migration from bulk to surface as well as at the interface between ZnIn₂S₄ and In(OH)₃. This work provides an efficient and eco-friendly strategy for one-pot synthesis of heterostructured composites with intimate contact for photocatalytic application.     

Simultaneously enhancing the thermal stability and electrochemical performance of solid polymer electrolytes by incorporating rod-like Zn2(OH)BO3 particles

Solid polymer electrolytes provide high safety and good electrochemical stability in solid-state lithium batteries (SSLBs) compared with conventional liquid electrolytes. In this work, a novel solid polymer composite electrolyte based on poly (ethylene oxide) (PEO) filled with rod-like Zn₂(OH)BO₃ particles was prepared by a grinding process followed with a heating treatment process and a cold pressing process. The effect of the incorporation amount of rod-like Zn₂(OH)BO₃ particles on the ionic conductivity was investigated systemically. It is found that 10 mol% of rod-like Zn₂(OH)BO₃ particles addition resulted in a highest ionic conductivity of 2.78 × 10⁻⁵ at 30 °C and the improved ionic conductivity was considered to be caused by the reducing of PEO crystallinity and the increasing of Li ion migrating pathway on the interface between the Zn₂(OH)BO₃ and PEO. In addition, the optimum composite electrolyte exhibited a high electrochemical stability window of 4.51 V (vs. Li/Li⁺), good lithium stability and excellent thermal stability.     

Fabrication of multi-filler thermoset-based composite bipolar plates for PEMFCs applications: Molding defects and properties characterizations

The bipolar plate (BP) material should possess contradictory properties. They should also manufacture from low-cost methods and materials. In the current investigation, thermoset-based composite materials reinforced with conductive fillers, and the compression molding process is implemented. In addition to fabricating the bipolar plates (BPs) with and without the flowing channels, alleviating the defects during the molding process is performed. The channels are perfectly formed on the plates with the designed depth of 0.65 mm and 0.5 mm of width. In the meanwhile, we alleviate different molding defects, which spoil the surface appearance and part properties. Regarding the physical properties, the water contact angle is measured to be around 85°. The through-plane electrical conductivity of molded plates showed high values up to 38 S/cm, and the interfacial contact resistance measured to be 18–24 mΩ cm². The mean value of the flexural strength of the produced samples was equal to 47 MPa, which is almost twice the DOE target (>25 MPa).     

Al-doping induced superior lithium ion storage capability of LiNiO2 spheres

To optimize the performance of LiNiO₂ with minimal modification of the pristine structure, a facile solid-state approach, based on the interdiffusion of elements at the solid/solid interface, is developed to achieve uniformly Al-doped LiNiO₂ using alumina coated Ni(OH)₂ spheres as the precursor. The resulting LiNi_0.95Al_0.05O₂ material exhibits excellent discharge capacity (209.9 mAh g⁻¹ at 0.1 C) and cycling stability with a capacity retention of 85.10% after 200 cycles at 0.5 C. This is ascribed to the improved reversibility of the phase transitions by Al-doping as revealed by in-situ XRD characterization. The Al-doping also endows the material with superior rate capability due to the enlarged interlayer spacing in the structure and alleviation of the side reactions at the electrode/electrolyte interface, favorable for lithium ion diffusion. An optimal amount of doped Al is necessary for ensuring the structure stability and interface ionic conductivity of the LiNiO₂ spheres. Thus, the present strategy may provide an opportunity to optimize the performance of LiNiO₂, with uniform doping of a small amount of Al, producing a promising cathode material for advanced lithium ion batteries.     

Using d-limonene as the non-aromatic and non-chlorinated solvent for the fabrications of high performance polymer light-emitting diodes and field-effect transistors

Aiming to environment protection, green solvents are crucial for commercialization of solution-processed optoelectronic devices. In this work, d-limonene, a natural product, was introduced as the non-aromatic and non-chlorinated solvent for processing of polymer light-emitting diodes (PLEDs) and organic field effect transistors (OFETs). It was found that d-limonene could be a good solvent for a blue-emitting polyfluorene-based random copolymer for PLEDs and an alternating copolymer FBT-Th₄(1,4) with high hole mobility (μ_h) for OFETs. In comparisons to routine solvent-casted films of the two conjugated polymers, the resulting d-limonene-deposited films could show comparable film qualities, based on UV–vis absorption spectra and observations by atomic force microscopy (AFM). With d-limonene as the processing solvent, efficient blue PLEDs with CIE coordinates of (0.16, 0.16), maximum external quantum efficiency of 3.57%, and luminous efficiency of 3.66 cd/A, and OFETs with outstanding μ_h of 1.06 cm² (V s)⁻¹ were demonstrated. Our results suggest that d-limonene would be a promising non-aromatic and non-chlorinated solvent for solution processing of conjugated polymers and molecules for optoelectronic device applications.